LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

Distributed learning consensus control based on neural networks for heterogeneous nonlinear multiagent systems

This paper considers a novel distributed iterative learning consensus control algorithm based on neural networks for the control of heterogeneous nonlinear multiagent systems. The system's unknown nonlinear function is approximated by suitable neural networks; the approximation error is countered by a robust term in the control. Two types of control algorithms, both of which utilize distributed learning laws, are provided to achieve consensus. In the provided control algorithms, the desired reference is considered to be an unknown factor and then estimated using the associated learning laws. The consensus convergence is proven by the composite energy function method. A numerical simulation is ultimately presented to demonstrate the efficacy of the proposed control schemes.     

600MW超临界CFB机组深度调峰运行技术

经通过分析超临界CFB机组在深度调峰方面的优势,结合600MW超临界CFB机组的实际运行工况,提出机组在深度调峰前应开展的试验工作。研究600MW超临界CFB机组的深度调峰过程,从汽机、锅炉、电气等方面提出有效的技术措施,解决深度调峰可能带来的锅炉流化不良、环保参数控制困难等问题。通过在600MW超临界CFB机组上应用,机组在30%负荷深度调峰运行,工况稳定,各项参数正常,取得了较好效果。     

不同润湿表面液体沸腾的分子动力学模拟

采用分子动力学方法研究纳米尺度下液氩在过热基板上的沸腾过程。通过调节固液间相互作用的方式改变壁面润湿性，模拟并分析了壁面润湿性对沸腾过程中能量传递和液体运动情况的影响。结果表明：不同润湿性表面均会发生固液分离的现象，但是固体表面附近吸附的氩原子数密度随润湿性增强而增大；润湿性较强时，液体的能量上升快，热通量高，液体内部温度梯度大，发生固液分离时间早，系统中氩的温度和能量低，上升过程中液氩密度、厚度变化小；润湿性较弱时，液体的能量上升慢，热通量小，液体内部温度梯度小，发生固液分离时间延后，系统中氩的温度、能量更高，上升过程中液氩密度、厚度变化较大。下部气体压力整体上大于上部气体压力，发生固液分离时润湿性越强的表面上液体上下压差越大，首次上升过程能达到的高度越高，所需时间越短。     

Development of LTCC micro-hotplate with PTC temperature sensor for gas-sensing applications

Low temperature co-fired ceramic (LTCC) micro-hotplates show wide applications in gas sensors and micro-fluidic devices. It is easily structured in three-dimensional structures. This paper presents the low power consumption micro-hotplates which were developed with PTC (positive temperature coefficient) temperature sensor and inter-digitated electrodes. The paper presents two different structures for micro-hotplate with platinum as a heating element. The PTC temperature sensor using two different materials viz. PdAg and platinum paste are developed with micro-hotplates. The simulation has been achieved through COMSOL for LTCC and alumina micro-hotplates. The temperature variation with power consumption has been measured for the developed LTCC micro-hotplates. The change in resistance of PTC temperature sensors was measured with micro-hotplate temperature. The aim of this study was to place a temperature sensor with the gas sensor module to measure and control the temperature of micro-hotplate. A SnO₂ sensing layer is coated on LTCC micro-hotplate using screen printing and characterized for the sensing of carbon monoxide gas (CO). This study will be beneficial for designing hotplates based on LTCC technology with low power consumption and better stability of temperature for gas-sensing applications.     

基于热电效应的高效环控系统

部分空间科学实验对环境温度有较高的要求，环境温度高于或低于空间科学系统能够提供的热沉温度，需要有可靠有效的加温降温处理措施。使用可靠性强的热电制冷片作为制冷制热方式和气液换热器二次换热来实现环境温度控制的需求，并对不同流体温度制冷制热效果进行分析，结果表明流体温度和目标温度差越小，热电制冷制热的效果越好。在环境温度制冷工况中，热电单元数量随电流增加先减少后增加，在制热工况中则单调递减，设计中需按照制冷工况进行热电单元数量的确定。当流体温度接近制冷制热的目标温度时，会出现整个系统总效率优于热电系统效率的区间。通过对热电单元和气液换热器的组合系统的性能计算，提供一种适于热电环控系统的计算方法和部件选型思路，对空间站环控系统的设计有重要参考意义。     

关于提升装载机电子秤检定结果测量准确度的探讨

装载机电子秤广泛应用于货场、建筑工地,如何使检定结果准确可靠,本文对自动衡器检定装置标准器量值的管理方法进行了一些探讨。     

A simple model for deep dynamic stall conditions

The present study is focused on modeling of dynamic stall behavior of a pitching airfoil. The deep stall regime is in particular considered. A model is proposed, which has a low implementation and computational complexity but yet is able to deal with different types of dynamic stall conditions, including those characterized by multiple vortex shedding at the airfoil leading edge. The proposed model is appraised against an extensive data set of experimental (α,C_L) curves for NACA0012. The results of an existing widely used model, having comparable complexity, are also shown for comparison. The proposed model is able to well reproduce not only the classic curves of deep dynamic stall but also the curves characterized by lift oscillations at high angles of attack due to the shedding of multiple vortices. Furthermore, the model appears to be robust to variations of its parameters from the optimal values and of the airfoil geometry. Finally, the model is successfully implemented in a commercial CFD software and applied to the simulation of a vertical axis wind turbine within the actuator cylinder approach. The accuracy of the prediction of the turbine power coefficient in the whole rotation cycle is very good for the optimal working condition of the turbine, for which the model parameters were calibrated. Fairly good accuracy is also obtained in significantly different working conditions without any further calibration.     

蓝莓溃疡病生防链霉菌CX3的抑菌效果及其鉴定

[目的]为了明确从吉林省长白山保护区池西保护站马鞍山云杉人工林林下土壤分离,所获得1株拮抗菌株(编号记为CX3)的生防效果及分类地位。[方法]分别采用平板对峙法和杯碟法测定该菌株活菌及其发酵液的抑菌活性和抑菌谱;并通过形态学、生理生化特征、16S rRNA序列分析等方法研究了其分类地位。[结果]该菌株对13种供试植物病原菌均有抑制作用,抑菌谱广,其中对蓝莓溃疡病菌有极强的抑制作用,抑菌带达25.91 mm,发酵液的抑菌圈直径达31.73 mm;根据其菌株形态、生理生化特性、16S rRNA序列比对,最终鉴定菌株为链霉菌属Streptomyces sp.。[结论]该菌株对蓝莓溃疡病菌有显著的抑制效果,应用开发前景良好,此次是国内首次报道该菌株杀真菌活性。     

综放工作面防治水技术应用实践

为解决21000工作面采空区及顶板涌水问题,根据工作面出水点的不同情况,采取了集水器导水、老塘设挡水堰截水、挖排水沟疏水等多项治水措施,经统计排水量达33~42m3/h,有效控制了水情,确保了工作面正常生产。